Sometimes, it is very difficult to carry your iPod or portable MP3 players in your car, because there is a risk for it to be damaged by the dashboard while driving. Brodit ProClip is an ultimate solution for this problem. Brodit ProClip holds it into one place and gives you a convenient access to your MP3 player.

The best thing about the Chrysler Neon Brodit ProClip is that you don’t need any special tool to install it. To install the Chrysler Neon Brodit ProClip Bracket just hook the angled edge on the upper part of the ProClip into in the gap in the padded dashboard. Now press the grooved edge on the lower part of it into the gap between the air vent frame and dashboard press until it snaps into place. Brodit ProClip is fixed in its place.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Chrysler Neon Brodit ProClip Bracket

Brodit ProClip Bracket is tough mounting solution for all your problems relating to the portability of your iPod and other portable MP3 players. It is also compatible with the Chevrolet Kalos. It saves your iPod from damages by the dashboard while driving.

It is easy to install this ProClip bracket. Just press the thin end of the enclosed gap openers between the center console panel frame and the padded dashboard. Then press grooved edge on the left side of the ProClip into the gap and pull out the gap openers. Now press the gap opener into the gap between the climate control panel and the coin box. Press it firmly on the right side of the ProClip put it into the gap opener. Press until you feel it snaps into place, then pull out the gap opener and your ProClip is in place.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Chevrolet Aveo Brodit ProClip Bracket

Brodit ProClip is used to keep your iPod to one place, and to secure it, from damaging by dashboard. There are car specific Brodit ProClip bracket available for BMW 630. These ProClip Brackets are also compatible with BMW 645 and BMW 650 Center mount cars.

To install the Brodit ProClip bracket, just peel off the cover of adhesive tape on the ProClip. After this hook the angled edge on the upper part of the ProClip over the panel frame. Pull the lower part towards against the gap between the air vent panel frames. Now push the lower part of the ProClip so, Brodit ProClip goes into the gap. Confirm that it has fit into its place and ProClip bracket is installed to its place.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our BMW 630 Brodit ProClip Bracket

You should have one radio removal tool for your car to save your delicate car radio, at the time of maintaining or servicing. Usually, different car radios are available for the different car radios, but thanks to the unique design of DIN Radio Removal Tool it is compatible with many car radios. DIN Radio Removal Keys can remove majority of radios as fitted in Ford, early Peugeot, Rover, Renault, Vauxhall car.

The car radio mentioned above has 1 or 2 holes at each side of the radio. DIN Radio Removal Tool is well suited for these kinds of radios. In the Vauxhall radio there are 4 small studs with the Allen keys, before you can insert the release keys.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our DIN Radio Removal Tool

If you drive a Daewoo and you want to install the iPod Car Kit cradles, mobile phone cradles and other portable devices, then here is the solution for you. Daewoo Espero Dashmount Bracket is tough, stylish and easy to install. It has a car specific design for the Daewoo car to give it an integrated look.

To install the Daewoo Espero Dashmount Bracket remove the two air vents and the two screws underneath the dashboard. Remove the upper part of the center console and place the dash mount arms around the edge of the left edge of the panel, which has the short angled arms behind it. After you have done this, press the console in position and restore the screws and air vent to its place and the Daewoo Espero Dashmount Bracket is installed in your car.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Daewoo Espero Dashmount Bracket

If you are looking for the tough mounting solution for your Chevrolet car, then Chevrolet Blazer Brodit ProClip Bracket can be the right solution for you. These brackets and accessories are designed exclusively for the Chevrolet car. These accessories are for the convenient access to your portable media player. The special design of this Brodit ProClip Bracket gives an integrated look with the dashboard of Chevrolet.

The best feature of the Chevrolet Brodit ProClip bracket includes stylish black finish and the tough ABS plastic design. These Brodit ProClip Brackets are extremely easy to install. You won’t need any special tool to install it and the interiors of the car will remain safe at the time of installation.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Chevrolet Blazer S10 Brodit ProClip Bracket

Radio removal tool is very essential for any car, especially those with the expensive radios such as clarion. If, you use one of the clarion radios, there is a special radio removal tool available for it. Most of the times, it happens that radio repair shop does not have proper tools to remove Clarion radio. Without these tools, there is always a chance to damage of these expensive radio sets. So, it is better to have one Clarion radio removal tool for your car radio.

1 locking tab system is used in most of the cars. With the unique design of the Clarion Radio Removal Tool it is literally effortless to remove the 1 locking tab system clarion radio.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Clarion Radio Removal Tool – set 1