The dashboard while driving often damages the iPod and other portable music players. This is the main reason, because of which most of the people do not like to carry your iPod in their car. But, now there is a solution for this problem. If you are driving Rover city car, then Rover City Rover Brodit ProClip Brackets could be the right solution for you.

The installation of this proclip can be done in a few seconds, without damaging your car. Remove the screw under the climate control panel. Push the gap opener into the gap to widen it and remove the cover of the adhesive tape on the ProClip. Now push the proclip bracket into the gap under the gap opener and pull the gap opener out. Press the lower part of the proclip in the hole and screw it with the removed screw. The proclip bracket is placed in your Rover city.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Rover City Rover Brodit ProClip Brackets

With this ProClip bracket in your car, you don’t have to think again in carrying your iPod again in your Renault Avantime. It is made of the high quality material, which is very durable. The Renault Avantime Brodit ProClip Bracket is made specifically to your Renault Avantime. It makes it safe to carry your iPod and also gives an easy access to your iPod in the car.

To install the Renault Avantime Brodit ProClip Bracket, you have to first peel off the adhesive tape covers on the ProClip. Now, push the lower part of the ProClip Bracket into the gap between the control panel and the stereo panel. Clip the ProClip into the gap between the dashboard and the surrounding frame. Push the ProClip forward until it goes into the gap.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Renault Avantime Brodit ProClip Bracket

Carrying an iPod is no longer a problem, thanks to the Nissan Quest Brodit ProClip bracket. This Brodit ProClip bracket is designed for the Nissan Quest, considering the needs of this car. The main advantage of this Brodit ProClip bracket is that your hands will always be near to your iPod. Because of this, you can operate your iPod easily even if you are driving your Nissan Quest.

To install the Nissan quest, press the thin end of the gap opener in the console wall. Now push the angled edges on the right side of the ProClip into the gap between the control panel and the surrounding panel frame. After you are done with this, push the left side of the ProClip. So, the angled edge will snap into the gap. Now simply pull out the gap opener. The ProClip is installed in the Nissan Quest.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Nissan Quest Brodit ProClip Bracket

Without the digital sound of the iPod, driving a stylish Mitsubishi does not create any impression. If you also want to carry your iPod in your Mitsubishi Lance, then Brodit ProClip bracket is a must for you. It is made from a special ABS plastic, which is finished in stylish black.

Damage free installation is another feature of this Brodit ProClip bracket. For the installation just follow these simple steps. Press the thin edge on the lower part of the ProClip bracket in the gap between the air vent frame and dash panel frame, until you hear it snap into one place. Widen the gap with the gap opener, if it is very tight. Follow the same procedure with the upper part and hook it into the gap between the panel frame and the padded dashboard. The installation is completed.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Mitsubishi Lancer Brodit ProClip Bracket

Mazda B-series Brodit ProClip not only secures your iPod from damage, but also gives an easy access to your car iPod. With the Brodit ProClip bracket installed in your car, you will be able to control your iPod even when you are driving. The main feature of the Mazda Brodit ProClip bracket is the integrated look and car specific design.

The following simple steps can do the installation of the Mazda B-series Brodit ProClip Bracket. Firstly, press the thin end of the enclosed gap opener into the gap between the surroundings of control panel and the dashboard. Press the lower part of the ProClip into the gap next to the gap opener and press the gap opener into the gap. Now, press the upper part of the ProClip into the gap and pull out the gap opener. The Mazda B-series Brodit ProClip Brackets is fixed with your car.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Mazda B-series Brodit ProClip Brackets

Brodit ProClip Brackets are those accessories, which secures the iPod and other portable media players from damage by the dashboard. There is a Brodit ProClip iPod available in the market, which is made especially for the Lexus ES 300 car. This Brodit ProClip is designed according to the needs of the Lexus ES 300.

Easy and damage free installation is one of the main feature of the Lexus ES 300. To install this Brodit ProClip bracket, peel off the cover of the adhesive tape on the ProClip and place it over the console edge. After this press the left side of the ProClip towards the floor, so that the angled edge hooks under the console frame. These simple steps attach Brodit ProClip to your Lexus ES 300.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Lexus ES 300 Brodit ProClip Bracket

Land Rover Brodit ProClip is the additional accessory for your iPod, which gives you a complete mounting solution for your Land Rover. The main advantage of the Land Rover Freelander Brodit ProClip is that it secures the iPod from the damage by the dashboard and gives you an easy access to your iPod.

The interiors of the car would not be damaged in the installation. To install the ProClip bracket, press the thin end of the enclosed gap opener into the gap between the control panel and the dashboard to widen the gap. Remove the adhesive tape cover on the ProClip and hook the right part of the ProClip. Then press the left side of the ProClip, so the edge of the Brodit ProClip into the gap above the gap opener. After all this, press the angled edge towards the control panel so it goes into the gap. Pull your gap opener and Brodit ProClip Bracket is attached to your Land Rover Freelander.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Land Rover Freelander Brodit ProClip Bracket

Brodit ProClip is a necessity for every car if you want to carry your iPod or any other portable music system in your car. If you install one of the Brodit ProClip Brackets in your Jeep wrangler, it would give you a safe and convenient access to your iPod. It holds the iPod to one place in the car, so it does not get damaged by the car dashboard.

It is really easy to install the Brodit ProClip in your jeep wrangler. To install the Brodit ProClip remove the adhesive tape on it, and press the lower part of the ProClip bracket into the gap below the dashboard. After this flip the ProClip towards the air vent, then lift it over the front part of the dashboard. Confirm that the Brodit ProClip has attached properly and the Brodit ProClip is attached to your Jeep Wrangler.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Jeep Wrangler Brodit ProClip Bracket

Hyundai Accent Brodit ProClip Bracket can be considered as an extremely useful accessory for all of those persons, who like to carry their iPod and portable MP3 player in their Hyundai Accent. It not only makes it convenient to operate the iPod but also protects it from damage.

The installation is really easy. Press the thin end of the enclosed gap opener into the gap between the dashboard and the control panel. Clean the surface with the use of alcohol pad. Push the fixing plate into the gap next to the gap opener and press this fixing plate away from the steering wheel towards the dashboard. Now you can pull out the gap opener. Now peel of the cover of the adhesive tape on the ProClip. Place the ProClip in such a way that the holes in the face-plate are placed over the holes in the fixing plate. Now put the screws in the holes and the Hyundai Accent Brodit ProClip Bracket is attached to your Hyundai accent.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Hyundai Accent Brodit ProClip Bracket

Sometimes, you must be feeling the difficulty to operate your iPod while driving the car. If you have this difficulty, try the Honda CR-V Brodit ProClip Bracket for your Honda CR-V. It will give you a convenient access to your iPod. Your iPod will also be protected from the damages caused by the dashboard, while driving.

It is easy to install the Honda CR-V Brodit ProClip Bracket. Remove the screw below the air vent in the frame surrounding it. After this peel off the adhesive tape cover on the ProClip and hook the ProClip over the air vent panel edge. It makes the hole in the ProClip to match the hole from the removed screw. Put the screw in the hole and in the hole in the panel. Check that ProClip is safely attached and it is fixed in its place.

Purchasing an iPod from our website would be ideal. You can go ahead and buy our Honda CR-V Brodit ProClip Bracket